Safety · 23 June 2026 · 6 min read
7 Signs Your Melbourne Home Needs a Switchboard Upgrade
Seven warning signs your Melbourne home needs a switchboard upgrade, from ceramic fuses and no safety switch to burning smells, plus what the job involves.
Your switchboard is the part of the house most people never look at until something goes wrong. It takes power from the meter and splits it into the circuits that run your lights, power points, oven, air conditioner and everything else. If it is old, overloaded or missing modern protection, the rest of your wiring is only as safe as that one panel.
Plenty of homes across Melbourne’s north, from 1960s and 70s brick veneers in Thomastown, Lalor and Reservoir to early 2000s builds in South Morang and Mernda, are running boards that were never designed for today’s loads. Here are seven signs it is time to have yours looked at by a licensed electrician.
Why the switchboard matters
A modern switchboard does two jobs. It protects the wiring from overload and short circuits using circuit breakers, and it protects people from electric shock using residual current devices (RCDs), which most people call safety switches. A board that cannot do both properly is a risk for fire and shock, no matter how good the wiring behind it is.
The 7 signs
1. You still have ceramic or rewireable fuses
If you open the switchboard door and see small porcelain fuse holders with fuse wire in them, your board is from a different era. Rewireable fuses are slow to react, easy to fix with the wrong wire, and offer no shock protection at all. A board like this may still “work”, but it is well past its use-by date and should be replaced rather than patched.
2. There is no safety switch, or only one
A safety switch cuts power in a fraction of a second when it detects electricity leaking to earth, which is exactly what happens when current passes through a person. Current Australian wiring rules call for RCD protection on the final circuits in a home, covering both power and lighting. Many older boards have none, or a single one covering only some of the power points.
If the property is a rental, Victoria’s minimum standards also require safety switches, which we cover in our rental electrical safety check guide.
3. The board is warm, buzzing or discoloured
Scorch marks, brown staining, a burning smell, a buzzing or crackling noise, or a switchboard door that feels warm to the touch all point to loose connections or overloaded components. Those are signs of heat, and heat is how electrical fires start.
Do not open the board to investigate. If you can switch off the main switch safely, do so and call an electrician straight away. If you see smoke or smell something strongly burning, call 000 first.
4. Breakers trip often, or won’t reset
An occasional trip can simply mean you ran the kettle, toaster and heater at once. But a board that trips constantly, breakers that feel loose or hot, or a safety switch that will not stay on, can mean worn components or a fault somewhere in the circuit. Our guide on why a safety switch keeps tripping walks through the safe checks you can do before calling.
5. Lights flicker or dim when appliances start
Lights that dim when the air conditioner or oven kicks in can be a sign of an overloaded circuit, but they can also point to a loose neutral connection in the board, at the meter or along the service cable. A loose neutral can cause voltage swings that damage appliances and, in the worst case, create a shock risk. It is not something to leave until next month.
6. You are adding solar, an EV charger or big appliances
Even a healthy older board can run out of room. A ducted air conditioner, induction cooktop, battery, solar inverter or home EV charger each want their own protected circuit. If there are no spare ways in the board, or the main switch and supply are already near their limit, the board needs upgrading before anything new goes in. We would rather tell you that up front than squeeze in a circuit that does not belong there.
7. The board is crowded, unlabelled or has been modified
Open a few switchboards and you will see the same story: extra circuits added over decades, two wires crammed under one terminal, cables passing through holes with no protection, handwritten labels that no longer match anything. DIY changes and unlicensed work are common causes. If nobody can tell you which breaker runs what, an electrician cannot work on it safely either.
A related warning: boards installed before the mid 1980s sometimes used backing panels containing asbestos. Do not drill, cut or sand around an old board. A licensed electrician can advise on safe handling before any work starts.
What a switchboard upgrade involves
A typical upgrade replaces the old board with a new one fitted with circuit breakers and safety switches across the power and lighting circuits, with every circuit labelled clearly. The electrician tests each circuit, checks the earthing, and confirms the wiring is in a condition to be reconnected. Some older homes need extra work, such as replacing deteriorated cables or fixing earthing problems we find along the way. We point those out before they become part of the job, never after.
Power is usually off for several hours, so plan around fridges, medical equipment and work-from-home needs. Where the supply to the house needs changes, such as a meter upgrade or a move from single phase to three phase, the electricity distributor gets involved and timing can stretch.
Switchboard replacement is prescribed electrical work in Victoria. That means it must be done by a licensed electrician, and we provide a Certificate of Electrical Safety for it, which is lodged with Energy Safe Victoria. Keep a copy with your home records, because insurers, buyers and future electricians may ask for it.
What it typically costs
Prices vary with the size of the home, the number of circuits, how much of the wiring needs attention and whether the supply needs work. As a broad guide, many switchboard upgrades on a typical Melbourne house fall somewhere between about $1,500 and $4,000, with larger homes or extra rectification work going higher. That is a guide only. We confirm a fixed price in writing before any work starts, so there are no surprises when the board is open.
Should you wait?
If you can tick off even one of the seven signs, get it looked at. Some, like ceramic fuses or a missing safety switch, are not an emergency but are well worth fixing on your timeline instead of during a fault. Others, like a warm board or burning smell, are not for waiting.
If you are buying an older home, a switchboard check before settlement is cheap insurance. An electrician can tell you in a short visit what you are inheriting.
Need a hand?
If your switchboard is showing any of these signs, call Anthony on 0413 682 993. We will take a look, explain what we find in plain English, and give you a fixed price before any work begins.